Imagine enjoying a warm shower after a tiring and cold day, and all of a sudden the water pressure goes down and ruins the mood for a good warm shower! Low water pressure can be very annoying especially if it hurdles your routine tasks or disrupts a peaceful bath after a tiring day.
However, today we will present you with some nifty tips and tricks to improve and augment your water pressure learned from MyHomeNeedz, so that you can go about your routine without the stress of incomplete tasks due to lack of water. So let’s see what to do and what not to do to improve the water pressure at your home.
Checking the pressure
Before you jump into the improvement of the pressure you will have to start by checking the normal pressure of the water and compare it to the times when it is low. So the first thing you need to do is to contact your neighbors and see if they are facing a similar pressure issue. If that is the case, your water pressure problem tones down a little. However, if that is not the case then you probably will have to carry out a few procedures to maintain good pressure.
If you are alone facing the pressure problem, start by measuring the pressure of water using a pressure gauge. A test gauge with a hose connection will allow you to verify your water pressure with that of the city. So start by screwing the gauge on a hose faucet. Then follow this by opening up the tap, and also make sure that any other water outlet is closed at that moment. According to some stats in the market, a 60 psi is a good pressure anything below this is regarded as low. And anything above 70 is regarded as high pressure.
Once you are done measuring the pressure you will need to perform one of the following techniques to ensure that your water pressure is back to its normal pace.
Clear up the clogging
If you happen to be living in a house a decade old, you may have to face this pressure reduction due to clogging. Over time, the pipes are prone to get clogged with dirt and other impurities, thereby affecting the water pressure. In most cases of excessive clogging, you will find the diameter of the wire reduced which prevents the water from flowing freely through the pipe to your faucets and showerheads.
While in serious cases, you may need to replace the pipe and fittings with brand new ones, you can overcome moderate clogging by simply cleaning up the drains and the faucet heads with vinegar and other solvents which dissolve up the impurities in the fittings. You can make use of the vinegar and baking soda solution and run that through your drain to open it up. To have a clog-free shower head, hand a zip lock bag filled with vinegar on the showerhead overnight. In the morning clean it up and enjoy a smooth water flow while showering.
Sometimes, the clogging is not the real issue causing a reduced pressure. If you are using a public facility when it comes to water, you might have a regulator installed to ensure a smooth stream of water throughout the house. And if this regulator goes bad, you will inevitably face water pressure issues. Check if your regulator is working fine or not.
If not, you will need to hire a plumber to get the job done. The plumber will look for the faulty regulator and replace it with a new one for you in no time.
Check for leaks
Leaks can be a hidden cause of water pressure becoming low from the source. You may experience water pressure to be different at different places in your house. If that is the case, you will need to check for leaks along the pipes and fixtures. A leak at any point will cause the water to divert its usual flow path thereby reducing the amount of flow per unit area.
To look for leaks, you will need to shut down the water supply of the entire home. Then check the water meter for the reading. Markdown the reading somewhere and check for the meter again after an hour or 2. An increased reading will indicate a possible leakage in some pipe around the house. In such a case you will need to contact the plumber who will then resolve the leakage issue for you.
Add a pressure pump
Sometimes it may not be your fault at all when it comes to the water pressure, the environment, your surroundings or the neighbour might be a potential cause of low water pressure at your home. The location of your house might be so that it requires the pumping of water uphill, which considerably reduces the pressure along the way. Or it could be that your neighbour tends to use more water and this leaves you with little flow when it comes to your turn.
In such a case, an easy way out is to boost the flow of the incoming water at the source. A pressure booster pump will do you wonders and will prevent any water pressure problem in the scenarios mentioned earlier. The thing is easy to install however, it does require some investment on your part. So if you do not mind spending a little extra, this is your best option to augment the water pressure at your home.
With these tricks, you will be able to get rid of all your water pressure related problems in no time. You will no longer be disappointed in a shower after a long tiring day; neither will you have to face soiled dishes after a full cycle of the dishwasher. So what is the wait, get up today and diagnose your water pressure, find the reason for the fault and then solve the problems using are nifty tips in no time!