DIY Miter Saw Stand |

DIY Miter Saw Stand |

I probably should have done this project forever and a half ago (like before I started re-doing our entire house), but I FINALLY got around to building a few workbenches and setting up my shop. And by “shop” I mean the garage. My goal is to maximize shop space and storage, but still be able to park the car in there when necessary. First things first – a DIY miter saw stand.

>This post may contain affiliate links. If you make a purchase from one of the links, I may make a small commission at NO EXTRA COST to you. This helps keep the tutorials and plans free here at Bitterroot DIY. Thank you for your support! See my full disclosure here.

I designed this miter saw stand to fit my saw and shop space, but there are a million and one ways to build one. Make sure to measure your saw, measure your space, and adjust the plans as necessary.


DIY miter saw stand

Tools & Supplies:


  • 14 | 2 x 4 @ 8′
  • 1 | 3/4″ sheet of particle board (or plywood)


  • 12 | 2 x 4 @ 36″ (full length legs)
  • 4 | 2 x 4 @ 32 1/2″ (mid-workbench legs)
  • 5 | 2 x 4 @ 18″ (top & bottom frame)
  • 4 | 2 x 4 @ 21″ (top frame)
  • 2 | 2 x 4 @ 44″ (top frame)
  • 2 | 2 x 4 @ 28″ (top frame)
  • 2 | 2 x 4 @ 13″ (top frame)
  • 2 | 2 x 4 @ 91″ (bottom frame) **Tip: cut these pieces after you build the three bench sections. Measure all three sections together and cut to fit. The full width may be a little more than 91″ due to connections. See Step 4.
  • 1 | 3/4″ Particle Board @ 47 1/2″ x 27″ (left tabletop)
  • 1 | 3/4″ Particle Board @ 31″ x 27″ (center tabletop)
  • 1 | 3/4″ Particle Board @ 16 1/2″ x 27″ (right tabletop)
  • 1 | 3/4″ Particle Board @ 91″ x 21″ (bottom shelf)

Step 1.

Build the three top frames according to the following diagrams.

I built three separate frames so that the miter saw section has its own frame, and the top of the saw table sits level with the bench on either side.

Left Frame:

DIY miter saw stand

Middle Frame:

DIY miter saw stand

Right Frame:

DIY miter saw stand

Use 2 1/2″ screws through the sides of the 2 x 4s to attach the frame pieces. You could use pocket holes if you want to hide all the screws, but I decided to screw things directly together since it’s just a workbench in the garage.

Step 2.

Lay the left frame on a level surface (I used the garage floor) and attach the legs with 2 1/2″ screws. It’s easiest to build the frame upside down to get the legs flush with the top of the frame and then flip it over.

DIY miter saw standLeft frame – iso

DIY miter saw standLeft frame – top

Repeat the same process for the middle frame.

DIY miter saw standMiddle frame – iso

DIY miter saw standMiddle frame – top

Repeat for the right frame.

DIY miter saw standRight frame – iso

DIY miter saw standRight frame – top

Step 3.

Build the bottom frame as shown below. Attach the boards with 2 1/2″ screws through the sides of the 2 x 4s.

** see my tip in the cut list above

DIY miter saw standBottom Frame

Step 4.

Line the three benches up next to each other and work the bottom frame into place.

DIY miter saw stand

I laid the benches on their backs to get the bottom frame into place and then attached the frame with 2 1/2″ screws through each of the legs.

DIY miter saw stand

Step 5.

Lastly, attach the tabletops and bottom shelf. I had the guys at Home Depot rip the particle board sheet into two strips – one 27″ wide for the tabletop and one 21″ wide for the bottom shelf. Then I cut the three tabletop pieces down to size with my circular saw.

DIY miter saw stand

If you add up the total length of all three tabletops, you’ll notice it is 1/2″ short of the full 8′ sheet. I did that to account for the blade width when you cut the sheet into three sections. It’s not a super exact measurement – the important part is that the middle section fits flush in between the right and left bench, and that the right and left tabletops are flush where they meet the middle bench so your saw can sit there without interference.

Use 1 1/4″ screws to attach the tabletops and shelf to the frame. I just countersunk the screws so they won’t catch on anything.

Go ahead and stain or seal the workbench if you want. I left mine unfinished, but it’s totally personal preference!

DIY miter saw stand

You may want to consider placing your miter saw in the center of the workbench. I offset mine to the right because of how the shop is set up (the bench doesn’t sit in the middle of the wall). Just make sure to take your space into account before you start building.

Please let me know if you have any questions and I’ll get back to you as soon as possible!

If you’d like more information, I’ve also saved a video tutorial for this workbench to my highlights on my Instagram.

Bitterroot DIY

>Thanks for stopping by!

>For more project ideas, you can find me on Pinterest. And to stay up to date with the latest shenanigans, follow me on Instagram.

DIY miter saw stand

Leave a Comment

0 Comments Made